Standard Taper Wheel Adapters.
3.000" TPF WITH 1.00" DIAMETER AT LARGE END OF TAPER. FOR 1.250" ID WHEELS.

FIG. 1

FIG. 2

FIG. 3


How did we create the Sopko legacy? Attention to detail and an unremitting commitment to quality that generations of grinding professionals have come to know as the unmatched standard of the industry. Today, customers are still asking for value, performance, and precision.
It's been nearly 50 years; we're still listening.

  • HIGH QUALITY INTERNAL TAPERS for precision mounting.

  • THREAD GROUND OD THREADS for maximum concentricity and squareness.

  • HEAT TREATED COMPONENT PARTS for strength and reliability.

  • CONCENTRIC and SQUARE GROUND SURFACES for better workpiece finishes.

  • BLACK OXIDE FINISH to protect your investment.


 

SOPKO CATALOG NO. FIG. SOPKO PART NO. DIMENSIONS
A C D E
00100 1 100-1  1/2 to 3/4 1-7/8 1-1/4-16LH  -
00102 1 100-2 1/2 to 3/4 1-7/8 1-1/4-16RH -
00105 1 100-1C 3/4  1-7/8 1-1/4-16LH -
00101* 2 AN100-1 1/2 to 3/4 1-7/8 1-1/4-16LH 3/16
50183* 2 AN100-2 1/2 to 3/4 1-7/8 1-1/4-16RH 3/16
00112 2 KW100-1 1/2 to 3/4 1-7/8 1-1/4-16LH 1/8
00200 1 200-1 1/4 to 1/2 1-3/4 1-1/4-16LH -
00202 1 200-2 1/4 to 1/2 1-3/4 1-1/4-16RH -
00208 1 K200-1 1/8 to 1/2 1-3/4 1-1/4-16LH -
00216 1 K200-2 1/8 to 1/2 1-3/4 1-1/4-16RH -
00217 1 200-1C 1/2 1-3/4 1-1/4-16LH -
00201* 2 AN200-1 1/4 to 1/2 1-3/4 1-1/4-16LH 3/16
00225* 2 AN200-2 1/4 to 1/2 1-3/4 1-1/4-16RH 3/16

00226

2 KW200-1 1/4 to 1/2 1-3/4 1-1/4-16LH 1/8
00227 2 KW200-2 1/4 to 1/2 1-3/4 1-1/4-16RH 1/8
00300 1 300-1 3/4 to 1 2-1/4 1-1/4-16LH -
00303* 2 AN-300-1 3/4 to 1 2-1/4  1-1/4-16LH 3/16
00308* 2 AN-300-2 3/4 to 1 2-1/4 1-1/4-16RH 3/16
00302 1 300-2  3/4 to 1 2-1/4 1-1/4-16RH -
00301 1 300-1B 1-1/2 2-11/16 1-1/4-16LH -
00304 1 300-2B 1-1/2 2-11/16 1-1/4-16RH -
00305 1 300-1C 1 2-1/4 1-1/4-16LH -
00306 1 300-2C 1 2-1/4 1-1/4-16RH -
00307 1 R300-2B 1/2 to 1-1/2 2-11/16 1-1/4-16RH -
50319 2 KW300-1 3/4 to 1 2-1/4 1-1/4-16LH 1/8
00686 2 KW300-2 3/4 to 1 2-1/4 1-1/4-16RH 1/8
00207 3 X200-1 1/4 to 1/2 1-3/4 1-1/4-16LH -
00245 3 X200-2 1/4 to 1/2 1-3/4 1-1/4-16RH -
*Furnished with two #10-32 nylon-tipped set screws 00939 on nut OD for reversing rotation applications


ROTATION:

RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.

William Sopko & Sons Co., Inc. ● 26500 Lakeland Blvd. ● Cleveland, Ohio 44132-2692 ● Order Desk (216) 289-1400 ● Fax (216) 289-1888

 

ROTATION:

RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.
CAUTION!
Always Wear Safety Goggles When Griding.

4

William Sopko & Sons Co., Inc. ● 26500 Lakeland Blvd. ● Cleveland, Ohio 44132-2692 ● Order Desk (216) 289-1400 ● Fax (216) 289-1888

 

Standard Taper Wheel Adapters.
3.000" TPF WITH 1.00" DIAMETER AT LARGE END OF TAPER. FOR 1.250" ID WHEELS.


Sopko is more than quality products; it's quality service too. You can be sure of quick personalized service every time you call. We know you don't have a lot of time to waste listening to phone recordings. You'll be talking to real people with answers to your grinding accessory needs.

  • SAME DAY shipment of standard product.

  • FRIENDLY and KNOWLEDGEABLE people with INFORMATION you need.

  • The LARGEST STOCK of precision grinding accessories in America.

  • The source for SPECIAL GRINDING ACCESSORIES made to your specifications.


 

SOPKO CATALOG NO. SOPKO PART NO. DIMENSIONS
A C D E
00400 400-1A 2 3-3/16 1-1/4-16LH -
00402 400-2A 2 3-3/16 1-1/4-16RH -
00401 400-1B 1 to 2    3-3/16 1-1/4-16LH -
00403 400-2B 1 to 2 3-3/16 1-1/4-16RH -
00406 400-1C 1-3/4 to 2 3-3/16 1-1/4-16LH -
00415 400-2C 1-3/4 to 2 3-3/16 1-1/4-16RH  -
00327* AN400-1B 1 to 2 3-3/16 1-1/4-16LH 3/16
00413 - 2-1/2 to 2-3/4 3-13/16 1-1/4-16LH  -
00414 - 2-1/2 to 2-5/8 3-3/4 1-1/4-16LH -

00500

500-1A 3 4-3/16 1-1/4-16LH -
00502 500-2A 3 4-3/16 1-1/4-16RH -
00501 500-1B 2 to 3 4-3/16 1-1/4-16LH -
00503 500-2B 2 to 3 4-3/16 1-1/4-16RH -
00506 500-1C 1-1/2 to 3 4-3/16 1-1/4-16LH -
00600 600-1A 4 5-3/16 1-1/4-16LH -
00602 600-2A 4 5-3/16 1-1/4-16RH -
00601 600-1B 3 to 4  5-3/16 1-1/4-16LH -
00604 600-2B 3 to 4 5-3/16 1-1/4-16RH -
00605 600-1C 3-5/8 to 4 5-3/16 1-1/4-16LH -
00701 700-1B 4-1/2 5-11/16 1-1/4-16LH -
00702 700-1C 5 6-3/16 1-1/4-16LH -
00800 800-1A 6 7-3/16 1-1/4-16LH -
00801 800-1B 5 to 6 7-3/16 1-1/4-16LH  -
00900 900-1A 7 8-3/16 1-1/4-16LH -
00999 1000-1A 8 9-3/16 1-1/4-16LH -
*Furnished with two #10-32 nylon-tipped set screws 00939 on nut OD for reversing rotation applications
 

ROTATION:

RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.
CAUTION!
Always Wear Safety Goggles When Griding.

5

William Sopko & Sons Co., Inc. ● 26500 Lakeland Blvd. ● Cleveland, Ohio 44132-2692 ● Order Desk (216) 289-1400 ● Fax (216) 289-1888

 

Standard Taper Wheel Adapters.
3.000" TPF WITH 1.00" DIAMETER AT LARGE END OF TAPER.  FOR 1.250" ID WHEELS.


00220 (220-1) is the standard replacement adapter for Bridgeport-Harig and Parker PM Majestic grinding machines using 7" diameter wheels.



 SOPKO
CATALOG NO. 
SOPKO PART NO. DIMENSIONS
D
00220 220-1 1-1/4-16LH
00221 220-2 1-1/4-16RH
Providing optimum protection against contamination to the wheelhead spindle nose, these high-quality SHROUDED ADAPTERS are designed for performance. Sopko assures this standard with quality features like PRECISION GROUND TAPERS and CONCENTRICALLY GROUND AND SQUARE surfaces to maximize cutting conditions and prolong wheel life. Hub OD threads are THREAD GROUND to assure safe, square wheel locking conditions and you can expect years of performance from these adapters because Sopko HEAT TREATS every one.



SOPKO CATALOG NO. SOPKO PART NO. DIMENSIONS
D
00180 2BY-LH 1-1/4-16LH
00181 2BY-RH 1-1/4-16RH

See page 60 for Pope style shrouded adapters.

 

ROTATION:

RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.
CAUTION!
Always Wear Safety Goggles When Griding.

6

William Sopko & Sons Co., Inc. ● 26500 Lakeland Blvd. ● Cleveland, Ohio 44132-2692 ● Order Desk (216) 289-1400 ● Fax (216) 289-1888

 

Standard Taper Wheel Adapters.
3.000" TPF WITH 1.00" DIAMETER AT LARGE END OF TAPER.  FOR 1.250", 1.500", AND 2.000" ID WHEELS.


SOPKO  PART NO.    SOPKO
CATALOG NO.
DIMENSIONS
A C D
00130 130-1 3/4

1-15/16

1-1/4-16LH
00132 130-2  3/4

1-15/16

1-1/4-16RH
00230 230-1 1/4 to 1/2

1-3/4

1-1/4-16LH
00232 230-2 1/4 to 1/2

1-3/4

1-1/4-16RH
00330 330-1  3/4 to 1

2-1/4

1-1/4-16LH
00332  330-2 3/4 to 1

2-1/4

1-1/4-16RH
00331 330-1S 3/8 to 1

2-1/4

1-1/4-16LH
00386  330-2S 3/8 to 1

2-1/4

1-1/4-16RH
00430    430-1A 2

3-1/4

1-1/4-16LH
00432 430-2A  2

3-1/4

1-1/4-16RH
00431    430-1B 1 to 2

3-1/4

1-1/4-16LH
00433 430-2B 1 to 2 3-1/4 1-1/4-16RH
00434 430-1D 2-1/4 to 2-1/2 

3-3/4

1-1/4-16LH
00435 430-1E 1-1/2 to 2

3-1/4

1-1/4-16LH

 

SOPKO
CATALOG NO.
SOPKO PART NO.    DIMENSIONS
A C D H
00333    330-1-1.500 1/2 to 1 2-1/4 1-1/4-16LH 1.500
00334 330-1-2.000 1/2 to 1 2-1/4 1-1/4-16LH 2.000

 

ROTATION:

RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.
CAUTION!
Always Wear Safety Goggles When Griding.

7

William Sopko & Sons Co., Inc. ● 26500 Lakeland Blvd. ● Cleveland, Ohio 44132-2692 ● Order Desk (216) 289-1400 ● Fax (216) 289-1888

 


Standard Taper Wheel Adapters.
3.000" TPF WITH 1.00" DIAMETER AT LARGE END OF TAPER.
FOR 1.250" ID WHEELS.

Play it safe with larger diameter wheels by using Sopko 3-1/2" OD wheel adapters. Manufactured with the same attention to detail, these Sopko adapters feature a high quality internal ground taper, thread ground OD threads, concentric and square ground surfaces, heat treated hub and nut with black oxide finish. Only Sopko offers all these valuable features.

00235

00337

SOPKO
CATALOG NO.
SOPKO
PART NO.
DIMENSIONS

A C D

00135 135-1 3/4 1-15/16 1-1/4-16LH

00235 235-1 1/4 to 1/2 1-3/4 1-1/4-16LH
00236 235-2 1/4 to 1/2 1-3/4 1-1/4-16RH

00335 335-1 3/4 to 1 2-1/4  1-1/4-16LH
00336 335-2 3/4 to 1 2-1/4 1-1/4-16RH
00337 335-1B 1-1/2 2-3/4 1-1/4-16LH
00618 335-2A 1/2 to 1 2-1/4 1-1/4-16RH

 

ROTATION:

RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.
CAUTION!
Always Wear Safety Goggles When Griding.

8

William Sopko & Sons Co., Inc. ● 26500 Lakeland Blvd. ● Cleveland, Ohio 44132-2692 ● Order Desk (216) 289-1400 ● Fax (216) 289-1888

 

Standard Taper Flanged Wheel Adapters.
3.000" TPF WITH 1.00" DIAMETER AT LARGE END OF TAPER. FOR 1.250" ID WHEELS.  DESIGNED FOR THIN CUT-OFF WHEELS AND DIAMOND WHEELS.


Sopko flanged adapters are machined from alloy steel. The resulting one piece hub design distributes mounting pressure away from the bore, the weakest part of the grinding wheel. The inherent rigidity of one piece design, and the precision ground flanges provide identical radial load bearing surfaces for positive wheel lock and better spindle driving torque to the abrasive wheel. All surfaces are ground concentric and square for optimum surface finishes. Completely heat treated, Sopko flanged adapters are safe to use and maintain their rigidity.


SOPKO
CATALOG NO.
SOPKO  PART NO. DIMENSIONS
A B D
00451 4.5-1 0 to 1/2 4-1/2 1-1/4-16LH
00452   4.5-2 0 to 1/2 4-1/2 1-1/4-16RH
00138 5.0-1 0 to 1/2  5 1-1/4-16LH
00139    5.0-2 0 to 1/2 5 1-1/4-16RH
00551   5.5-1 0 to 1/2 5-1/2 1-1/4-16LH
00552 5.5-2 0 to 1/2  5-1/2 1-1/4-16RH
00610 6.0-1 0 to 1/2  6 1-1/4-16LH
00612   6.0-2 0 to 1/2 6 1-1/4-16RH
00650   6.5-1 0 to 1/2 6-1/2 1-1/4-16LH
00652   6.5-2 0 to 1/2 6-1/2 1-1/4-16RH

ROTATION:
RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.

William Sopko & Sons Co., Inc. ● 26500 Lakeland Blvd. ● Cleveland, Ohio 44132-2692 ● Order Desk (216) 289-1400 ● Fax (216) 289-1888

 

ROTATION:

RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.
CAUTION!
Always Wear Safety Goggles When Griding.

9

William Sopko & Sons Co., Inc. ● 26500 Lakeland Blvd. ● Cleveland, Ohio 44132-2692 ● Order Desk (216) 289-1400 ● Fax (216) 289-1888

 


Standard Taper Flanged Wheel Adapters.
3.000" TPF WITH 1.00" DIAMETER AT LARGE END OF TAPER.
FOR 1.250" ID WHEELS.

All the quality features you expect from Sopko are built into these larger diameter flanged wheel adapters too...
  • ONE PIECE HUB design for rigidity.
  • PRECISION INTERNAL TAPER for proper spindle mating.
  • Completely HEAT TREATED for strength and years of use.
  • Precision GROUND FLANGE SURFACES for reliable wheel lock.
  • Concentric and square GROUND SURFACES for better surface finishes.
  • All external threads are THREAD GROUND for concentricity and squareness.
00710
(Front Side) (Taper Side)

SOPKO
CATALOG NO.
SOPKO
PART NO.
DIMENSIONS

A B C D

00710 7.0-1 0 to 1/2 7 1-7/8 1-1/4-16LH
00712 7.0-2 0 to 1/2 7 1-7/8 1-1/4-16RH

00750 7.5-1 0 to 1/2 7-1/2 1-7/8 1-1/4-16LH
00752 7.5-2 0 to 1/2 7-1/2 1-7/8 1-1/4-16RH

00810 8.0-1 0 to 1/2 8 2 1-1/4-16LH
00812 8.0-2 0 to 1/2 8 2 1-1/4-16RH

See page 74 for available flanges.
 

ROTATION:

RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.
CAUTION!
Always Wear Safety Goggles When Griding.

10

William Sopko & Sons Co., Inc. ● 26500 Lakeland Blvd. ● Cleveland, Ohio 44132-2692 ● Order Desk (216) 289-1400 ● Fax (216) 289-1888

 

Standard Taper Flanged Wheel Adapters.
3.000" TPF WITH 1.00" DIAMETER AT LARGE END OF TAPER.* FOR 2.000" AND 3.000" ID WHEELS.


Now you can extend the useful working life of 2.000" and 3.000" ID grinding wheels. There is no need to waste money by throwing worn wheels away. Extend wheel life, use Sopko 4-1/2" flanged diameter wheel adapters! Machined from forged alloy steel, the one-piece hub design distributes mounting pressure away from the bore, the weakest part of the grinding wheel. The inherent rigidity of one piece design and the precision ground flanges provide identical radial load bearing surfaces for positive wheel lock and better spindle driving torque to the abrasive wheel. All surfaces are ground concentric and square for optimum surface finishes. Completely heat treated, Sopko flanged adapters are safe to use and maintain their rigidity.

All the quality features you expect from Sopko are built into these flanged wheel adapters for 2.000" ID and 3.000" ID grinding wheels.

  • ONE PIECE HUB design for rigidity.

  • PRECISION INTERNAL TAPER for proper spindle mating.

  • Completely HEAT TREATED for strength and years of use.

  • Precision GROUND FLANGE SURFACES for reliable wheel lock.

  • Concentric and square GROUND SURFACES for better surface finishes.

  • All external threads are THREAD GROUND for concentricity and squareness.

  • Not for larger surface grinders (taper is 1.00" at LE).
     


SOPKO
PART NO.   
SOPKO CATALOG NO. DIMENSIONS
A C D H
00453    4.5-1-2 3/8 to 3/4 2-1/8

1-1/4-16LH

2.00
00454   4.5-2-2 3/8 to 3/4 2-1/8  1-1/4-16RH 2.00
00455   4.5-1-3 3/8 to 1 2-3/8  1-1/4-16LH 3.00
00456     4.5-2-3 3/8 to 1 2-3/8 1-1/4-16RH 3.00

ROTATION:
RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.

William Sopko & Sons Co., Inc. ● 26500 Lakeland Blvd. ● Cleveland, Ohio 44132-2692 ● Order Desk (216) 289-1400 ● Fax (216) 289-1888

 

ROTATION:

RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.
CAUTION!
Always Wear Safety Goggles When Griding.

11

William Sopko & Sons Co., Inc. ● 26500 Lakeland Blvd. ● Cleveland, Ohio 44132-2692 ● Order Desk (216) 289-1400 ● Fax (216) 289-1888

 


Standard Taper Balancing Wheel Adapters
for Small Surface Grinders.*
3.000" TPF WITH 1.00" DIAMETER AT LARGE END OF TAPER.
FOR 1.250" ID WHEELS.

Sopko balancing rings have milled pockets with 180° arc-length. One end of the arc is permanently stamped with a reference line and arrow to designate direction of rotation. Unlike some balancing rings, Sopko “sandwiches” the milled pockets together inside the mated faces. Grinding grit can’t build up! Rings are lapped flat and ground for a precision fit. A nylon-tipped set screw secures each ring to the adapter hub. All balancing adapters furnished with a 3/32" hex wrench 00938.
00565 00106

SOPKO
CATALOG NO.
SOPKO
PART NO.
DIMENSIONS

A C D E

00106 B100-1 1/2 to 3/4 1-7/8 1-1/4-16LH -
00107 B100-2 1/2 to 3/4 1-7/8 1-1/4-16RH -

00260 B200-1 1/4 to 1/2 1-3/4 1-1/4-16LH -
00262 B200-2 1/4 to 1/2 1-3/4 1-1/4-16RH -

00310 B300-1 3/4 to 1 2-1/4 1-1/4-16LH -
00311 B300-1B 1-1/2 2-11/16 1-1/4-16LH -
00313 B300-1C 1 2-1/4 1-1/4-16LH -
00312 B300-2 3/4 to 1 2-1/4 1-1/4-16RH -
50331** ANB300-2 3/4 to 1 2-1/4 1-1/4-16RH 3/16
00338 B300-2B 1-1/2 2-11/16 1-1/4-16RH -

00404 B400-1A 2 3-3/16 1-1/4-16LH -

Use Sopko Balancing Adapters to:

  • Increase productivity.

  • Reduce downtime and maintenance.

  • Produce low micro-finishes.

  • Reduce wheel wear and truing frequency.

  • Reduce costly spindle failures.

00405 B400-2A 2 3-3/16 1-1/4-16RH -
00410 B400-1B 1 to 2 3-3/16 1-1/4-16LH -
00412 B400-2B 1 to 2 3-3/16 1-1/4-16RH -

00504 B500-1A 3 4-3/16 1-1/4-16LH -
00565 B500-1B 2 to 3 4-3/16 1-1/4-16LH -
00505 B500-2A 3 4-3/16 1-1/4-16RH -
50305 B600-1B 3 to 4 5-3/16 1-1/4-16LH -
50393 B1000-1A 8 9-3/16 1-1/4-16LH -

**Furnished with two #10-32 nylon-tipped set screws 00939 on nut OD for reversing rotation applications.

00228


SOPKO
CATALOG NO.
SOPKO
PART NO.
DIMENSIONS

A C D F

00228 B200-1LH1-5/8 1/4 to 1/2 3-3/8 1-1/4-16LH 2-5/16
00229 B200-2RH1-5/8 1/4 to 1/2 3-3/8 1-1/4-16RH 2-5/16
00244 B200-1LH2-3/4 1/4 to 1/2 4-1/2 1-1/4-16LH 3-7/16
00219 B200-2RH2-3/4 1/4 to 1/2 4-1/2 1-1/4-16RH 3-7/16

*Most Sopko adapters can be furnished with balancing rings.
*See page 65, 66, 67, 68, and 69 for large taper balancing adapters for larger grinders.
*See page 90, 91, and 92 for balancing stands and accessories.

 

ROTATION:

RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.
CAUTION!
Always Wear Safety Goggles When Griding.

12

William Sopko & Sons Co., Inc. ● 26500 Lakeland Blvd. ● Cleveland, Ohio 44132-2692 ● Order Desk (216) 289-1400 ● Fax (216) 289-1888

 


Standard Taper Flanged Balancing
Wheel Adapters For Small Surface Grinders.*

3.000" TPF WITH 1.00" DIAMETER AT LARGE END OF TAPER.
FOR 1.250", 2.000", AND 3.000" ID WHEELS.

With operator safety in mind, Sopko offers a selection of balancing adapters having a variety of diameters for larger OD wheels. At Sopko the focus is always on operator safety; that’s why we designed and made these balancing adapters with precision internal tapers and thread ground OD threads. And that’s not all, we heat treat component parts for strength and grind all surfaces square and concentric for truly flat bearing surfaces. For safety, increased productivity, low-micro finishes, and reduced wheel wear, insist on Sopko large OD balancing adapters.

00460
00248 00251
(Front Side) (Taper Side)

SOPKO
CATALOG NO.
FIG. SOPKO
PART NO.
DIMENSIONS

A B C D H

00248 1 B220-1 1/4 to 1/2 2-7/16 1-3/4 1-1/4-16LH 1.250

00250 1 B130-1 3/4 3 1-15/16 1-1/4-16LH 1.250

00326 1 - 3/8 to 3/4 3-1/2 3-1/2 1-1/4-16LH 1.250
00315 1 B135-1 3/4 3-1/2 1-15/16 1-1/4-16LH 1.250

00251 1 B230-1 1/4 to 1/2 3 1-3/4 1-1/4-16LH 1.250
00579 1 B230-2 1/4 to 1/2 3 1-3/4 1-1/4-16RH 1.250

00339 1 B330-1D 1/4 to 1 3 2-1/4 1-1/4-16LH 1.250
00340 1 B330-2D 1/4 to 1 3 2-1/4 1-1/4-16RH 1.250
00436 1 B330-1 3/4 to 1 3 2-1/4 1-1/4-16LH 1.250
00437 1 B330-2 3/4 to 1 3 2-1/4 1-1/4-16RH 1.250

00438 1 B430-1A 2 3 3-1/4 1-1/4-16LH 1.250
00439 1 B430-1B 1 to 2 3 3-1/4 1-1/4-16LH 1.250
00440 1 B430-2A 2 3 3-1/4 1-1/4-16RH 1.250
00441 1 B430-2B 1 to 2 3 3-1/4 1-1/4-16RH 1.250

00555 1 - 1/4 to 1 4-1/4 2-1/2 1-1/4-16LH 1.250
00696 1 - 1/4 to 1 4-1/4 2-1/2 1-1/4-16RH 1.250

00458 2 B4.5-1 0 to 1/2 4-1/2 1-7/8 1-1/4-16LH 1.250
00459 3 B4.5-1-2 3/8 to 3/4 4-1/2 2-1/8 1-1/4-16LH 2.000
00460 3 B4.5-1-3 3/8 to 1 4-1/2 2-3/8 1-1/4-16LH 3.000

*Most Sopko adapters can be furnished with balancing rings.
*See page 65, 66, 67, 68, and 69 for large taper balancing adapters for larger grinders.
*See page 90, 91, and 92 for balancing stands and accessories.

 

ROTATION:

RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.
CAUTION!
Always Wear Safety Goggles When Griding.

13

William Sopko & Sons Co., Inc. ● 26500 Lakeland Blvd. ● Cleveland, Ohio 44132-2692 ● Order Desk (216) 289-1400 ● Fax (216) 289-1888

 

Standard Taper Long Extended Wheel Adapters.
3.000" TPF WITH 1.00" DIAMETER AT LARGE END OF TAPER.  FOR 1.250" ID WHEELS.

FIG. 1

FIG. 2


Sopko LONG EXTENDED ADAPTERS are designed to provide added clearance by locating the grinding wheel further from the spindle nose. These adapters are ideal for surface grinder applications where the operator must reach across a boss or other obstruction in order to grind. The adapters have also found wide application on cutter grinders and tap grinders.


 
SOPKO 
CATALOG NO.      
FIG. SOPKO PART NO. DIMENSIONS
A C D E F
00901 1 200-1LH-1/4 1/4 to 5/8 2 1-1/4-16LH - 15/16
00203 1 200-1LH-1-5/8 1/4 to 1/2 3-3/8 1-1/4-16LH - 2-5/16
00204 1 200-2RH-1-5/8  1/4 to 1/2  3-3/8 1-1/4-16RH - 2-5/16
50315 1 200-1LH1-5/8KW 1/4 to 1/2  3-3/8 1-1/4-16LH 1/8 2-5/16
05256 1 200-1E-1-5/8 2-1/4 5-1/16 1-1/4-16LH - 2-5/16
00252* 2 S200-1D-1-5/8 1-3/4 4-1/2 1-1/4-16LH  - 2-5/16
00254 1 200-1D-1-5/8 1-3/4 4-1/2 1-1/4-16LH - 2-5/16
00214 1 200-1LH-2-3/4 1/4 to 1/2 4-1/2 1-1/4-16LH - 3-7/16
00215 1 200-2RH-2-3/4 1/4 to 1/2 4-1/2 1-1/4-16RH - 3-7/16

 

ROTATION:
RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.

William Sopko & Sons Co., Inc. ● 26500 Lakeland Blvd. ● Cleveland, Ohio 44132-2692 ● Order Desk (216) 289-1400 ● Fax (216) 289-1888

 

ROTATION:

RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.
CAUTION!
Always Wear Safety Goggles When Griding.

14

William Sopko & Sons Co., Inc. ● 26500 Lakeland Blvd. ● Cleveland, Ohio 44132-2692 ● Order Desk (216) 289-1400 ● Fax (216) 289-1888

 


Standard Taper Cup Wheel Extended Adapters.
3.000" TPF WITH 1.00" DIAMETER AT LARGE END OF TAPER.
FOR 1.250" ID WHEELS.

Sopko cup wheel adapters are made with a THIN WALL FRONT FLANGE design to give maximum usage of cup wheel depth. Fully HEAT TREATED and made from SOLID BAR STOCK, Sopko cup wheel extension adapters are RIGID to provide positive wheel lock. A hardened and ground nut locks the wheel from the back of the adapter. Because of this nut configuration, RH threads are used for CW spindle rotation and LH threads are used for CCW rotation; providing a safe locking system that WILL NOT LOOSEN UP during spindle rotation.

00263 00265

SOPKO
CATALOG NO.
SOPKO
PART NO.
DIMENSIONS

C D

00263 200-1CW 2-1/2 1-1/4-16LH
00264 200-2CW 2-1/2 1-1/4-16RH
00265 - 3-1/2 1-1/4-16LH
00266 - 3-1/2 1-1/4-16RH

*Grinding wheel not included.

 

ROTATION:

RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.
CAUTION!
Always Wear Safety Goggles When Griding.

15

William Sopko & Sons Co., Inc. ● 26500 Lakeland Blvd. ● Cleveland, Ohio 44132-2692 ● Order Desk (216) 289-1400 ● Fax (216) 289-1888

 

Standard Taper Short I.D. Wheel Extensions.*
3.000" TPF WITH 1.00" DIAMETER AT LARGE END OF TAPER.  FOR A SMALL RADIUS OR THAT ONE SMALL SLOT.  SAVE THE EXPENSE AND SET-UP TIME OF A HIGH SPEED ATTACHMENT.


All SHORT IDWEs come with a floating nut spacer 00662 (FN-1), two flanges, and a wheel end-nut. The hex spindle nut must be selected separately to suit your machine. Most grinders use 1/2-13LH or 1/2-13RH threads. A 1-1/4" wrench flat on the body makes installation and removal easy.

CHECK THESE FEATURES!

  • ALL DIAMETERS GROUND for concentricity.

  • PRECISION INTERNAL TAPER for proper spindle mating.

  • ALL COMPONENT PARTS HEAT TREATED for strength and long life.

  • THREAD GROUND EXTERNAL THREADS for maximum concentricity and squareness.

  • SPECIALS can be made to your requirements. Please specify wheel OD, width, and ID.

SOPKO   CATALOG NO.     SOPKO PART NO. DIMENSIONS
A B C D
00759 200-3/8LH-S 1/2 to 3/4 1-1/2 3-7/8 3/8-16LH HEX
00760 200-3/8RH-S 1/2 to 3/4  1-1/2 3-7/8 3/8-16RH HEX
00761 1/2 to 3/4 2 3-7/8 3/8-16LH HEX
00762 1/2 to 3/4  2 3-7/8 3/8-16RH HEX
00763 200-1/2LH-S 3/8 to 5/8 1-1/2 3-7/8 1/2-13LH HEX
00764 200-1/2RH-S 3/8 to 5/8 1-1/2 3-7/8 1/2-13RH HEX
00765 3/8 to 5/8 2 3-7/8 1/2-13LH HEX
00766 3/8 to 5/8 2 3-7/8 1/2-13RH HEX
00769 1/2 2 3-7/8 5/8-18LH HEX
00770 1/2 2 3-7/8 5/8-18RH HEX
00773 1/2 2 4 3/4-16LH HEX
00774 1/2 2 4 3/4-16RH HEX
00775 200-1LH-S 1/2 2-1/2 4 1-20LH ROUND
00776 200-1RH-S 1/2 2-1/2 4 1-20RH ROUND


Standard Taper Long I.D. Wheel Extensions.*
3.000" TPF WITH 1.00" DIAMETER AT LARGE END OF TAPER.
FOR A SMALL RADIUS OR THAT ONE SMALL SLOT.
SAVE BOTH THE EXPENSE AND SET-UP TIME OF A HIGH SPEED ATTACHMENT.

All LONG IDWEs come with a floating nut spacer 00662 (FN-1), two flanges, and a wheel end-nut. The hex spindle nut must be selected separately to suit your machine. Most grinders use
1/2-13LH or 1/2-13RH threads. A 13/16” wrench flat on the step makes installation and removal easy. See page 76 for available hex spindle nut sizes. Extends grinding wheels 13/16" further from spindle nose than the short series ID wheel extensions shown on page 16.

00777 00783

00787 00791

SOPKO
CATALOG NO.
SOPKO
PART NO.
DIMENSIONS

A B C D

00777 200-3/8LH-L 1/2 to 3/4 1-1/2 4-13/16 3/8-16LH HEX
00778 200-3/8RH-L 1/2 to 3/4 1-1/2 4-13/16 3/8-16RH HEX
00779 1/2 to 3/4 2 4-13/16 3/8-16LH HEX
00780 1/2 to 3/4 2 4-13/16 3/8-16RH HEX

00781 200-1/2LH-L 3/8 to 5/8 1-1/2 4-13/16 1/2-13LH HEX
00782 200-1/2RH-L 3/8 to 5/8 1-1/2 4-13/16 1/2-13RH HEX
00783 3/8 to 5/8 2 4-13/16 1/2-13LH HEX
00784 3/8 to 5/8 2 4-13/16 1/2-13RH HEX

00787 1/2 2 4-13/16 5/8-18LH HEX
00788 1/2 2 4-13/16 5/8-18RH HEX

00791 1/2 to 1 2 4-13/16 3/4-16LH HEX
00792 1/2 to 1 2 4-13/16 3/4-16RH HEX

*For smaller wheels, ID wheel extensions can be supplied with wheelscrews.
*See page 74 for available flanges.

ROTATION:
RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.

 

 

ROTATION:

RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.
CAUTION!
Always Wear Safety Goggles When Griding.

16

William Sopko & Sons Co., Inc. ● 26500 Lakeland Blvd. ● Cleveland, Ohio 44132-2692 ● Order Desk (216) 289-1400 ● Fax (216) 289-1888

 


Standard Taper Long I.D. Wheel Extensions.*
3.000" TPF WITH 1.00" DIAMETER AT LARGE END OF TAPER.
FOR A SMALL RADIUS OR THAT ONE SMALL SLOT.
SAVE BOTH THE EXPENSE AND SET-UP TIME OF A HIGH SPEED ATTACHMENT.

All LONG IDWEs come with a floating nut spacer 00662 (FN-1), two flanges, and a wheel end-nut. The hex spindle nut must be selected separately to suit your machine. Most grinders use
1/2-13LH or 1/2-13RH threads. A 13/16” wrench flat on the step makes installation and removal easy. See page 76 for available hex spindle nut sizes. Extends grinding wheels 13/16" further from spindle nose than the short series ID wheel extensions shown on page 16.

00777 00783

00787 00791

SOPKO
CATALOG NO.
SOPKO
PART NO.
DIMENSIONS

A B C D

00777 200-3/8LH-L 1/2 to 3/4 1-1/2 4-13/16 3/8-16LH HEX
00778 200-3/8RH-L 1/2 to 3/4 1-1/2 4-13/16 3/8-16RH HEX
00779 1/2 to 3/4 2 4-13/16 3/8-16LH HEX
00780 1/2 to 3/4 2 4-13/16 3/8-16RH HEX

00781 200-1/2LH-L 3/8 to 5/8 1-1/2 4-13/16 1/2-13LH HEX
00782 200-1/2RH-L 3/8 to 5/8 1-1/2 4-13/16 1/2-13RH HEX
00783 3/8 to 5/8 2 4-13/16 1/2-13LH HEX
00784 3/8 to 5/8 2 4-13/16 1/2-13RH HEX

00787 1/2 2 4-13/16 5/8-18LH HEX
00788 1/2 2 4-13/16 5/8-18RH HEX

00791 1/2 to 1 2 4-13/16 3/4-16LH HEX
00792 1/2 to 1 2 4-13/16 3/4-16RH HEX

*For smaller wheels, ID wheel extensions can be supplied with wheelscrews.
*See page 74 for available flanges.

 

ROTATION:

RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.
CAUTION!
Always Wear Safety Goggles When Griding.

17

William Sopko & Sons Co., Inc. ● 26500 Lakeland Blvd. ● Cleveland, Ohio 44132-2692 ● Order Desk (216) 289-1400 ● Fax (216) 289-1888

 

Standard Taper Collet Chuck Extensions.
3.000" TPF WITH 1.00" DIAMETER AT LARGE END OF TAPER.  FOR A SMALL RADIUS OR THAT ONE SMALL SLOT.  SAVE BOTH THE EXPENSE AND SET-UP TIME OF A HIGH SPEED ATTACHMENT.


Widely used on surface grinders, the set includes a 1/4" 6000 series collet 59108, collet nut 59125, and floating nut spacer 00662 (FN-1). A 1-1/4" wrench flat on the body makes installation and removal easy.  The hex spindle nut must be selected separately to suit your machine.*

THERE IS A DIFFERENCE WITH SOPKO!

  • Collet Chuck Quills are ground all over for true CONCENTRICITY and BALANCE.

  • Tapers are PRECISION GROUND at both ends of the collet chuck extension adapter.

  • Made from AMERICAN SUPERIOR QUALITY alloy steel and heat treated for optimum performance.

  • The hardened collet nut has a precision internal taper that seats PRECISELY against the collet nose angle to assure PROPER ENGAGEMENT of the grinding wheel shank.

SOPKO
CATALOG NO. 
SOPKO PART NO. DIMENSIONS
C
00246 200-CCEA-S 2-15/16
00249 200-CCEA-L 4-15/16

6000 SERIES COLLETS**
RANGE 1/8" TO 1/2"

SOPKO
CATALOG NO.
COLLET CAPACITY
59100 1/8
59102 5/32
59104 3/16
59106 7/32
59108 1/4
59112 5/16
59116 3/8
59120 7/16
59124 1/2
59125 NUT
**Additional collet sizes are available on special order.


ROTATION:
RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.

William Sopko & Sons Co., Inc. ● 26500 Lakeland Blvd. ● Cleveland, Ohio 44132-2692 ● Order Desk (216) 289-1400 ● Fax (216) 289-1888

 

ROTATION:

RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.
CAUTION!
Always Wear Safety Goggles When Griding.

18

William Sopko & Sons Co., Inc. ● 26500 Lakeland Blvd. ● Cleveland, Ohio 44132-2692 ● Order Desk (216) 289-1400 ● Fax (216) 289-1888

 


Standard Taper Male Extensions.
3.000" TPF WITH 1.00" DIAMETER AT LARGE END OF TAPER.

SHORT MALE EXTENSIONS provide increased utility because grinding wheels already mounted do not need to be dismounted. This feature is especially useful when grinding with diamond wheels. Units come complete with floating nut spacer 00662 (FN-1) and 1/2-13 wheel end-nut. A 1-1/8” wrench flat on the body makes installation and removal easy. The hex spindle nut must be selected separately to suit your machine.*

00237
LONG MALE EXTENSIONS are designed for even greater clearance possibilities with their added reach. Units come complete with floating nut spacer 00662 (FN-1) and 1/2-13 wheel end-nut.

00257

SOPKO
CATALOG NO.
SOPKO
PART NO.
DIMENSIONS

C D F

00237 200-3-1/2LH 5-1/4 1/2-13LH HEX 3-1/2
00238 200-3-1/2RH 5-1/4 1/2-13RH HEX 3-1/2
00257 200-5LH 6-5/8 1/2-13LH HEX 4-7/8
00258 200-5RH 6-5/8 1/2-13RH HEX 4-7/8

* See page 76 for available hex spindle nut sizes.
 

ROTATION:

RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.
CAUTION!
Always Wear Safety Goggles When Griding.

19

William Sopko & Sons Co., Inc. ● 26500 Lakeland Blvd. ● Cleveland, Ohio 44132-2692 ● Order Desk (216) 289-1400 ● Fax (216) 289-1888

 

Standard Taper Reversible Wheel Adapters.
3.000" TPF WITH 1.00" DIAMETER AT LARGE END OF TAPER.  DESIGNED FOR 1.250" ID DIAMOND, CBN, AND VITRIFIED WHEELS.


THERE IS A DIFFERENCE WITH SOPKO REVERSIBLE ADAPTERS!

  • Formed wheels are used either way without redressing.

  • Can be REVERSED without DISMOUNTING the wheel for prolonged square corner life of diamond wheels.

  • Sopko reversible wheel adapters make it possible to use the same dressed angle for
    BOTH RIGHT AND LEFT GROUND TOOL BITS.

  • EASY TO USE-Just remove the adapter from the spindle nose and REMOUNT in the reverse direction.

  • SAFE TO USE-Sopko reversible wheel adapters are manufactured with a double-taper and are securely locked against loosening by the wheel rotation.

  • Manufactured from quality steel to withstand the rigors of daily use, then HARDENED and GROUND.
     

For use on all spindles having a 3.000" TPF with 1.00" diameter at large end of taper.  Including: Boyar-Schultz, Bridgeport, Brown & Sharpe, DoAll, Excello, Foote Burt-Hammond, Harig, Norton, Parker Majestic, Pope, Reid, Sanford, Setco, Taft Pierce, and Whitnon.

A precision ground double-taper and removable bushing make wheel mounting in opposite directions safe and reliable. Grinding wheel edges wear during use, but obtaining a new sharp edge is as easy as reversing the adapter on the spindle. LH thread is standard.

SOPKO 
CATALOG NO.
SOPKO PART NO.   DIMENSIONS
A B D
00222    222RWA 1/4 to 1/2 2-1/4 1-1/4-16LH
00255   222RWA-R 1/4 to 1/2 2-1/4 1-1/4-16RH
00256  4.5-2RWA 0 to 1/2 4-1/2 1-1/4-16RH
00022  22-W Replacement tapered bushing.


 

ROTATION:
RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.

William Sopko & Sons Co., Inc. ● 26500 Lakeland Blvd. ● Cleveland, Ohio 44132-2692 ● Order Desk (216) 289-1400 ● Fax (216) 289-1888

 

ROTATION:

RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.
CAUTION!
Always Wear Safety Goggles When Griding.

20

William Sopko & Sons Co., Inc. ● 26500 Lakeland Blvd. ● Cleveland, Ohio 44132-2692 ● Order Desk (216) 289-1400 ● Fax (216) 289-1888

 


Standard Taper Wheel Adapters For Metric Bore Wheels.*
3.000" TPF WITH 1.00" DIAMETER AT LARGE END OF TAPER.
FOR 32MM (1.217") ID WHEELS.

00174 00176

For 32MM Metric Bore Wheels


FIG. 1

00170 00172

For 32MM Metric Bore Wheels


FIG. 2


SOPKO
CATALOG NO.
FIG. SOPKO
PART NO.
DIMENSIONS

A C D

00170 1 1-100-1 1/2 to 3/4 1-7/8 1-1/4-16LH
00171 1 1-100-2 1/2 to 3/4 1-7/8 1-1/4-16RH

00172 1 2-200-1 1/4 to 1/2 1-3/4 1-1/4-16LH
00173 1 2-200-2 1/4 to 1/2 1-3/4 1-1/4-16RH

00174 1 3-300-1 3/4 to 1 2-1/4 1-1/4-16LH
00175 1 3-300-2 3/4 to 1 2-1/4 1-1/4-16RH

00176 2 2-230-1 1/4 to 1/2 1-3/4 1-1/4-16LH

*Other metric sizes quoted on request.

 
 
 

ROTATION:

RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.
CAUTION!
Always Wear Safety Goggles When Griding.

21

William Sopko & Sons Co., Inc. ● 26500 Lakeland Blvd. ● Cleveland, Ohio 44132-2692 ● Order Desk (216) 289-1400 ● Fax (216) 289-1888

 

 


Standard Taper Electroless Nickel Plated Adapters.
3.000" TPF WITH 1.00" DIAMETER AT LARGE END OF TAPER.
FOR 1.250" ID WHEELS.

When corrosive coolants pose special problems, choose Sopko ELECTROLESS NICKEL PLATED wheel adapters to reduce the high cost of replacement. Widely used in ELECTROLYTIC GRINDING machine applications and the RUBBER ROLL GRINDING INDUSTRY, Electroless Nickel plating deposits a uniformly dense coating of nickel-phosphorus alloy onto the adapter surface.

Sopko Electroless Nickel coatings offer you...
  • A HARD PROTECTIVE SHELL providing outstanding protection against wear and abrasion.
  • AN ECONOMICAL ALTERNATIVE to stainless steel or hard chrome finishes.
  • UNCOMMON CORROSION RESISTANCE to today’s harsh coolant environments.

00345

   00348

                   00366


SOPKO
CATALOG NO.
SOPKO
PART NO.
DIMENSION

A C D E

00345 EN100-1 1/2 to 3/4 1-7/8 1-1/4-16LH -
00346 EN100-2 1/2 to 3/4 1-7/8 1-1/4-16RH -
00347 EN100-1C 3/4 1-7/8 1-1/4-16LH -

00348 EN200-1 1/4 to 1/2 1-3/4 1-1/4-16LH -
00349 EN200-2 1/4 to 1/2 1-3/4 1-1/4-16RH -
00350* ENA200-1 1/4 to 1/2 1-3/4 1-1/4-16LH 3/16
00351* ENA200-2  1/4 to 1/2 1-3/4 1-1/4-16RH 3/16
00352** ENK200-1 1/8 to 1/2 1-3/4 1-1/4-16LH -
00353** A2031-1 1/8 to 5/8 1-3/4 1-1/4-16LH -
00355 EN200-1C 1/2 1-3/4 1-1/4-16LH -

00364 EN300-1 3/4 to 1 2-1/4 1-1/4-16LH -
00365 EN300-2 3/4 to 1 2-1/4 1-1/4-16RH -
00368 EN300-1C 1 2-1/4 1-1/4-16LH -
00369 EN300-2C 1 2-1/4 1-1/4-16RH -
00356 A2031-2 3/8 to 1 2-1/4 1-1/4-16LH -

00366 EN300-1B 1-1/2 2-11/16 1-1/4-16LH -
00367 EN300-2B 1-1/2 2-11/16 1-1/4-16RH -
00370 A2031-5 3/8 to 1-1/2 2-11/16 1-1/4-16LH -

Electroless nickel plating available on all Sopko adapters at additional cost.
*Comes with two #10-32 nylon-tipped set screws 00939 on nut OD for reversing rotation applications.
** Keyway to face.

 

ROTATION:

RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.
CAUTION!
Always Wear Safety Goggles When Griding.

22

William Sopko & Sons Co., Inc. ● 26500 Lakeland Blvd. ● Cleveland, Ohio 44132-2692 ● Order Desk (216) 289-1400 ● Fax (216) 289-1888

 


Standard Taper Electroless Nickel Plated Adapters.
3.000" TPF WITH 1.00" DIAMETER AT LARGE END OF TAPER.
FOR 1.250" ID WHEELS.

When corrosive coolants pose special problems, choose Sopko ELECTROLESS NICKEL PLATED wheel adapters to reduce the high cost of replacement. Widely used in ELECTROLYTIC GRINDING machine applications and the RUBBER ROLL GRINDING INDUSTRY, Electroless Nickel plating deposits a uniformly dense coating of nickel-phosphorus alloy onto the adapter surface.
Sopko

Electroless Nickel coatings offer you...
  • A HARD PROTECTIVE SHELL providing outstanding protection against wear and abrasion.
  • AN ECONOMICAL ALTERNATIVE to stainless steel or hard chrome finishes.
  • UNCOMMON CORROSION RESISTANCE to today’s harsh coolant environments.


FIG. 1
00373 00377

SOPKO
CATALOG NO.
FIG. SOPKO
PART NO.
DIMENSIONS

A C D

00371 1 EN400-1A 2 3-3/16 1-1/4-16LH
FIG. 2
00372 1 EN400-2A 2 3-3/16 1-1/4-16RH
00373 1 EN400-1B 1 to 2 3-3/16 1-1/4-16LH
00374 1 EN400-2B 1 to 2 3-3/16 1-1/4-16RH

00376 1 EN500-1A 3 4-3/16 1-1/4-16LH
00377 1 EN500-1B 2 to 3 4-3/16 1-1/4-16LH
00378 1 A2031-4 1-3/4 to 3 4-3/16 1-1/4-16LH

00379 1 EN600-1A 4 5-3/16 1-1/4-16LH

00357 2 EN200-1LH1-5/8 1/4 to 1/2 3-3/8 1-1/4-16LH

Electroless nickel plating available on all Sopko adapters at additional cost.

 

ROTATION:

RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.
CAUTION!
Always Wear Safety Goggles When Griding.

23

William Sopko & Sons Co., Inc. ● 26500 Lakeland Blvd. ● Cleveland, Ohio 44132-2692 ● Order Desk (216) 289-1400 ● Fax (216) 289-1888

 


Standard Taper Electroless Nickel Plated Adapters.
3.000" TPF WITH 1.00" DIAMETER AT LARGE END OF TAPER.
FOR 1.250" AND 3.000" ID WHEELS.

If corrosive coolants pose special problems for you, choose Sopko ELECTROLESS NICKEL PLATED wheel adapters to reduce the high cost of replacement. Widely used in ELECTROLYTIC GRINDING machine applications and the RUBBER ROLL GRINDING industry, Electroless Nickel plating deposits a uniformly dense coating of nickel-phosphorus alloy onto the adapter surface.

Sopko Electroless Nickel coatings offer you...
  • A HARD PROTECTIVE SHELL providing outstanding protection against wear and abrasion.
  • AN ECONOMICAL ALTERNATIVE to stainless steel or hard chrome finishes.
  • UNCOMMON CORROSION RESISTANCE to today’s harsh coolant environments.

FIG. 1
01112 00651

00358 00360


FIG. 2
SOPKO
CATALOG NO.
FIG. SOPKO
PART NO.
DIMENSIONS

A B C D H

00140 1 EN220-1 1/4 to 1/2 2-7/16 1-3/4 1-1/4-16LH 1.250
00358 1 EN220-2 1/4 to 1/2 2-7/16 1-3/4 1-1/4-16RH 1.250

00359 1 EN330-1 3/4 to 1 3 2-1/4 1-1/4-16LH 1.250

00360 1 EN430-1B 1 to 2 3 3-1/4 1-1/4-16LH 1.250
01111 1 EN430-2B 1 to 2 3 3-1/4 1-1/4-16RH 1.250
01914 * 1 ENB430-1B 1 to 2 3 3-1/4 1-1/4-16LH 1.250
00361 * 1 ENB430-2B 1 to 2 3 3-1/4 1-1/4-16RH 1.250

01112 2 EN4.5-1 0 to 1/2 4-1/2 1-7/8 1-1/4-16LH 1.250
00974 2 EN4.5-2 0 to 1/2 4-1/2 1-7/8 1-1/4-16RH 1.250

00380 2 EN4.5-1-3 3/8 to 1 4-1/2 2-3/8 1-1/4-16LH 3.000

50397 2 EN5.0-1 0 to 1/2 5 1-7/8 1-1/4-16LH 1.250

01249 2 EN5.5-1 0 to 1/2 5-1/2 1-7/8 1-1/4-16LH 1.250

00136 2 EN6.0-1 0 to 1/2 6 1-7/8 1-1/4-16LH 1.250
00137 2 EN6.0-2 0 to 1/2 6 1-7/8 1-1/4-16RH 1.250

00651 2 EN6.5-2 0 to 1/2 6-1/2 1-7/8 1-1/4-16RH 1.250

Electroless nickel plating available on all Sopko adapters at additional cost.
*Balancing style adapter.

 

ROTATION:

RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.
CAUTION!
Always Wear Safety Goggles When Griding.

24

William Sopko & Sons Co., Inc. ● 26500 Lakeland Blvd. ● Cleveland, Ohio 44132-2692 ● Order Desk (216) 289-1400 ● Fax (216) 289-1888

 


Standard Taper Stainless Steel Wheel Adapters.
3.000" TPF WITH 1.00" DIAMETER AT LARGE END OF TAPER.
FOR 1.250" ID WHEELS.

Made from 300 series stainless steel, and designed for applications that require the ultimate in corrosion resistance, these adapters are used widely in medical applications. They are anti-magnetic, which makes them ideal for cutting slots or grooves in magnetic materials. Hub, washer, and nut are all made from 300 series stainless steel.
00259
00267

SOPKO
CATALOG NO.
SOPKO
PART NO.
DIMENSIONS

A D

00259 SS100-1 3/8 to 3/4 1-1/4-16LH
00261 SS100-2 3/8 to 3/4 1-1/4-16RH
00211 S100/200-1 1/2 to 3/4 1-1/4-16LH
00267 SS100/200-2 1/2 to 3/4 1-1/4-16RH
 

ROTATION:

RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.
CAUTION!
Always Wear Safety Goggles When Griding.

25

William Sopko & Sons Co., Inc. ● 26500 Lakeland Blvd. ● Cleveland, Ohio 44132-2692 ● Order Desk (216) 289-1400 ● Fax (216) 289-1888

 


Standard Taper Wheel Adapters
With 3/32” Keyway in Small End of Taper.*

FOR GRINDING MACHINES MANUFACTURED BY UNISON CORP., FERNDALE, MI.
3.000" TPF WITH 1.00" DIAMETER AT LARGE END OF TAPER.
FOR 1.250" ID WHEELS.


00719 00716

Note: 3/32"
Keyway in small
end of taper only

FIG. 1
00721

SOPKO
CATALOG NO.
FIG. SOPKO
PART NO.
DIMENSIONS

A C D F

00716 1 U200-1 1/4 to 1/2 1-3/4 1-1/4-16LH -
00717** 1 BU200-1 1/4 to 1/2 1-3/4 1-1/4-16LH -
00718 1 U200-2 1/4 to 1/2 1-3/4 1-1/4-16RH -

00719 2 U200-1LH1-5/8 1/4 to 1/2 3-3/8 1-1/4-16LH 2-5/16
FIG. 2
00720 2 U200-2RH1-5/8 1/4 to 1/2 3-3/8 1-1/4-16RH 2-5/16
00721 2 U200-1LH2-3/4 1/4 to 1/2 4-1/2 1-1/4-16LH 3-7/16
00423 2 U200-2RH2-3/4 1/4 to 1/2 4-1/2 1-1/4-16RH 3-7/16

00722 1 U300-1 3/4 to 1 2-1/4 1-1/4-16LH -
00709 1 U300-2 3/4 to 1 2-1/4 1-1/4-16RH -
00723 1 U300-1B 1-1/2 2-11/16 1-1/4-16LH -
00193** 1 BU300-1 3/4 to 1 2-1/4 1-1/4-16LH -

Standard taper wheel adapters can be made with the 3/32" keyway in the taper.
List above is stocked product only.
* NOTE: The keyway is parallel to the centerline of the adapter.
**Balancing style adapter. See page 12 and 13 for other balancing style adapters.

 

ROTATION:

RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.
CAUTION!
Always Wear Safety Goggles When Griding.

26

William Sopko & Sons Co., Inc. ● 26500 Lakeland Blvd. ● Cleveland, Ohio 44132-2692 ● Order Desk (216) 289-1400 ● Fax (216) 289-1888

 


Standard Taper Wheel Adapters
With 3/32” Keyway in Small End of Taper.*

FOR GRINDING MACHINES MANUFACTURED BY UNISON CORP., FERNDALE, MI.
3.000" TPF WITH 1.00" DIAMETER AT LARGE END OF TAPER.
FOR 1.250” ID WHEELS.



FIG. 1


FIG. 2
Note: 3/32"
Keyway in small
end of taper only
 
00725

SOPKO
CATALOG NO.
FIG. SOPKO
PART NO.
DIMENSIONS

A C D

00724 1 U400-1A 2 3-3/16 1-1/4-16LH
00725 1 U400-1B 1 to 2 3-3/16 1-1/4-16LH
00726 1 U400-2A 2 3-3/16 1-1/4-16RH
00727** 1 BU400-1B 1 to 2 3-3/16 1-1/4-16LH

00728 1 U500-1A 3 4-3/16 1-1/4-16LH
50320 1 U500-2A 3 4-3/16 1-1/4-16RH
00729 1 U500-1B 2 to 3 4-3/16 1-1/4-16LH

00730 1 U600-1A 4 5-3/16 1-1/4-16LH
00606 1 U600-1B 3 to 4 5-3/16 1-1/4-16LH

00732 2 U330-1 3/4 to 1 2-1/4 1-1/4-16LH
00733 2 U430-1A 2 3-1/4 1-1/4-16LH
00734 2 U430-1B 1 to 2 3-1/4 1-1/4-16LH

Standard taper wheel adapters can be made with the 3/32" keyway in the taper.
List above is stocked product only.
* NOTE: The keyway is parallel to the centerline of the adapter.
**Balancing style adapter. See page 12 and 13 for other balancing style adapters.

 

ROTATION:

RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.
CAUTION!
Always Wear Safety Goggles When Griding.

27

William Sopko & Sons Co., Inc. ● 26500 Lakeland Blvd. ● Cleveland, Ohio 44132-2692 ● Order Desk (216) 289-1400 ● Fax (216) 289-1888

 


Standard Taper Wheel Adapters With Ball Location.
3.000" TPF WITH 1.00" DIAMETER AT LARGE END OF TAPER.
FOR 1.250" ID WHEELS.


FIG. 1


FIG. 2


FIG. 3


FIG. 4

CNC grinders have multiple set-ups requiring wheel location repeatability. To hold this constant wheel position, Sopko adapters are ground to a precision BALL LOCATION, which establishes a constant relationship between the adapter taper and wheel face.

We’ll Help You with CNC Grinding!
  • BALL LOCATION for CNC REPEATABILITY.
  • GROUND external threads for SAFETY you can count on.
  • PRECISION internal taper for RELIABLE spindle mounting.
  • CONCENTRIC and SQUARE surfaces for a BETTER WORKPIECE FINISH.
  • BLACK OXIDE finish and completely HEAT TREATED for years of use.

00739

00738

00737


SOPKO
CATALOG NO.
FIG. SOPKO
PART NO.
DIMENSIONS

A B C D E

00157 1 100-2BALL 1/2 to 3/4 2-1/4 1-7/8 1-1/4-16RH -
00477 1 200-2BALL 1/4 to 1/2 2-1/4 1-3/4 1-1/4-16RH -

00736* 1 U200-1BALL 1/4 to 1/2 2-1/4 1-3/4 1-1/4-16LH 3/32
00737* 1 U400-1BBALL 1 to 2 2-1/4 3-3/16 1-1/4-16LH 3/32
00469 1 600-2BBALL 4 2-1/4 5-3/16 1-1/4-16RH -

00268** 2 200-1LH-1-5/8BALL 1/4 to 1/2 2-1/4 3-3/8 1-1/4-16LH -
00269*** 2 AN200-1LH1-5/8BALL 1/4 to 1/2 2-1/4 3-3/8 1-1/4-16LH 3/16

00738* 3 EU230-1BALL 1/4 to 1/2 3 1-3/4 1-1/4-16LH 3/32

50337* 3 U430-1BBALL 1 to 2 3 3-1/4 1-1/4-16RH 3/32

00739* 4 U4.5-1BALL 0 to 1/2 4-1/2 1-7/8 1-1/4-16LH 3/32

* NOTE: The keyway is parallel to the centerline of the adapter in the small end of the taper only.
**See page 48 for other Huffman Grinder adapters.
***Comes with two #10-32 nylon-tipped set screws 00939 on nut OD for reversing rotation applications.
 

ROTATION:

RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.
CAUTION!
Always Wear Safety Goggles When Griding.

28

William Sopko & Sons Co., Inc. ● 26500 Lakeland Blvd. ● Cleveland, Ohio 44132-2692 ● Order Desk (216) 289-1400 ● Fax (216) 289-1888

 


Standard Taper Wheel Adapters
With Glare Gear Assembly.

3.000" TPF WITH 1.00" DIAMETER AT LARGE END OF TAPER.
FOR 1.250" ID WHEELS.

The UNIQUE GRINDING WHEEL LOCKING SYSTEM that eliminates damage to grinding wheels and spindle bearings caused by hammering. Also provides best possible mounting concentricity when tightening diamond, CBN, or vitrified wheels.


FIG. 1
01231** 01235

SOPKO
CATALOG NO.
FIG. SOPKO
PART NO.
DIMENSIONS

A B C D E F
FIG. 2

01231 1 GG100-1 1/2 to 3/4 2-1/4 1-7/8 1-1/4-16LH - -
01232 1 GG100-2 1/2 to 3/4 2-1/4 1-7/8 1-1/4-16RH - -

01233 1 GG200-1 1/4 to 1/2 2-1/4 1-3/4 1-1/4-16LH - -
01234 1 GG200-2 1/4 to 1/2 2-1/4 1-3/4 1-1/4-16RH - -

01235 1 GG220-1 1/4 to 1/2 2-7/16 1-3/4 1-1/4-16LH - -

01236 1 GG300-1 3/4 to 1 2-1/4 2-1/4 1-1/4-16LH - -
01237 1 GG300-2 3/4 to 1 2-1/4 2-1/4 1-1/4-16RH - -
00159 1 GG300-1B 1-1/2 2-1/4 2-11/16 1-1/4-16LH - -

00127 1 GG400-1A 2 2-1/4 3-3/16 1-1/4-16LH - -
00566 1 GG400-2A 2 2-1/4 3-3/16 1-1/4-16RH - -
00189 1 GG400-1B 1 to 2 2-1/4 3-3/16 1-1/4-16LH - -

00417 1 GG500-1A 3 2-1/4 4-3/16 1-1/4-16LH - -
00462 1 GG500-2A 3 2-1/4 4-3/16 1-1/4-16RH - -
00704 1 GG500-1B 2 to 3 2-1/4 4-3/16 1-1/4-16LH - -
01282 3 GG200-1LH1-5/8 1/4 to 1/2 2-1/4 3-3/8 1-1/4-16LH - 2-5/16
00687 3 GG200-1LH2-3/4 1/4 to 1/2 2-1/4 4-1/2 1-1/4-16LH - 3-7/16

00740* 2 GGU100-1 1/2 to 3/4 2-1/4 1-7/8 1-1/4-16LH 3/32 -
FIG. 3
00741* 2 GGU100-2 1/2 to 3/4 2-1/4 1-7/8 1-1/4-16RH 3/32 -
00742* 2 GGU200-1 1/4 to 1/2 2-1/4 1-3/4 1-1/4-16LH 3/32 -
00743* 2 GGU200-2 1/4 to 1/2 2-1/4 1-3/4 1-1/4-16RH 3/32 -
00744* 2 GGU300-1 3/4 to 1 2-1/4 2-1/4 1-1/4-16LH 3/32 -
00745* 2 GGU300-2 3/4 to 1 2-1/4 2-1/4 1-1/4-16RH 3/32 -
00746* 2 GGU300-1B 1-1/2 2-1/4 2-11/16 1-1/4-16LH 3/32 -
00747* 2 GGU400-1A 2 2-1/4 3-3/16 1-1/4-16LH 3/32 -
00748* 2 GGU400-2A 2 2-1/4 3-3/16 1-1/4-16RH 3/32 -
00194* 2 GGU400-1B 1 to 2 2-1/4 3-3/16 1-1/4-16LH 3/32 -
00324* 2 GGU500-1A 3 2-1/4 4-3/16 1-1/4-16LH 3/32 -
00548* 2 GGU500-1B 2 to 3 2-1/4 4-3/16 1-1/4-16LH 3/32 -
00320* 3 GGU200-1LH1-5/8 1/4 to 1/2 2-1/4 3-3/8 1-1/4-16LH 3/32 2-5/16
00595* 3 GGU200-1LH2-3/4 1/4 to 1/2 2-1/4 4-1/2 1-1/4-16LH 3/32 3-7/16
50329* 3 GGU200-2RH1-5/8 1/4 to 1/2 2-1/4 3-3/8 1-1/4-16RH 3/32 2-5/16

See page 73 for complete selection of Glare Gear components.
Glare Gear Assemblies can be furnished with all 1-1/4" ID adapters.
List above is stocked product only.
*For grinding machines manufactured by Unison Corp., Ferndale, MI.
**Grinding wheel not included.
 

ROTATION:

RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.
CAUTION!
Always Wear Safety Goggles When Griding.

29

William Sopko & Sons Co., Inc. ● 26500 Lakeland Blvd. ● Cleveland, Ohio 44132-2692 ● Order Desk (216) 289-1400 ● Fax (216) 289-1888

 


Standard Taper Pin Slot Wheel Adapters
for Reversing Spindles.*

3.000" TPF WITH 1.00" DIAMETER AT LARGE END OF TAPER.
FOR 1.250" ID WHEELS.
USED ON NORTON NO. 20 TOOL AND CUTTER GRINDERS AND OLD STYLE HUFFMAN GRINDERS.


FIG. 1

FIG. 2

FIG. 3

FIG. 4


00094 00275

00209

00272


SOPKO
CATALOG NO.
FIG. SOPKO
PART NO.
DIMENSIONS

A B C D

F


00270 1 PS100-1 1/2 to 3/4 2-1/4 1-7/8 1-1/4-16LH -
00209 1 PS200-1 1/4 to 1/2 2-1/4 1-3/4 1-1/4-16LH -
00271 1 PS200-2 1/4 to 1/2 2-1/4 1-3/4 1-1/4-16RH -
00272 1 PS300-1 3/4 to 1 2-1/4 2-1/4 1-1/4-16LH -

00094 1 PS130-1 3/4 3 1-15/16 1-1/4-16LH -

00275 2 PS4.5-1 0 to 1/2 4-1/2 1-7/8 1-1/4-16LH -

00198** 3 - 3/8 to 1/2 2-1/4 2 1-1/4-16RH 15/16
00212 3 PS200-1LH1-5/8 1/4 to 1/2 2-1/4 3-3/8 1-1/4-16LH 2-5/16
00213 3 PS200-2RH1-5/8 1/4 to 1/2 2-1/4 3-3/8 1-1/4-16RH 2-5/16
00089 3 PS200-1LH2-3/4 1/4 to 1/2 2-1/4 4-1/2 1-1/4-16LH 3-7/16
00090 3 PS200-2RH2-3/4 1/4 to 1/2 2-1/4 4-1/2 1-1/4-16RH 3-7/16

00276 4 PS200-2CW-1-5/8 1/2 2-1/4 2-1/2 1-1/4-16RH -
00277 4 PS200-2CW-2-5/8 1/2 2-1/4 3-1/2 1-1/4-16RH -

*Most Sopko adapters can be modified with a pin slot.
List above is stocked product only.
**Has 5/16" pin slot.
 

ROTATION:

RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.
CAUTION!
Always Wear Safety Goggles When Griding.

30

William Sopko & Sons Co., Inc. ● 26500 Lakeland Blvd. ● Cleveland, Ohio 44132-2692 ● Order Desk (216) 289-1400 ● Fax (216) 289-1888

 


Large Taper Bolt-On Flange Balancing Wheel
Adapters for Larger Grinders.

3.000" TPF WITH 1.62" AND 2.25" DIAMETER AT LARGE END OF TAPER.
FOR 3.000" AND 5.000" ID WHEELS.



FIG. 1


FIG. 2


01812


00839

01353
(Front Side)

01351
(Taper Side)


SOPKO
CATALOG NO.

FIG.

DIMENSIONS


A

B

C

H


01351*†

1

1 to 1-1/2

7

3

5.000


01353*

1

1

4-15/16

2-1/2

3.000


01355**•

2

2-1/4 to 3

7

5-1/2

5.000



OPTIONAL SOCKET HEAD CAP SCREW SETS.


ADAPTER

WHEEL WIDTH
RANGE

SCREW SET
CATALOG NO.

SCREW SIZE

SET
QTY


01351

1 to 1-1/4

01812

5/16-18X2

6

1-1/2

01813

5/16-18X2-1/2

6


01353

3/4 to 1

01814

1/4-20X2

4

01355

2-1/4 to 2-1

01806

5/16-18X2

6

2-3/4 to 3

01807

5/16-18X2-1/2

6



01865

Three piece bronze balancing weight set for 01353.

00839

Three piece bronze balancing weight set for 01351.

00840

Three piece bronze balancing weight set for 01355.


All balancing style adapters include the three piece bronze balancing weight set.
See page 12 and 13 for standard taper balancing adapters.
* Price does not include optional nut 3/4-16LH 05020, 3/4-16RH 05021 on page 76 or snap ring 04291.
** Price does not include optional nut 7/8-14LH 05116, 7/8-14RH 05117 on page 76 or snap ring 04305.
Manufactured with snap ring groove. Snap ring not included.
Select proper length screw sets from tabulation to lock specific grinding wheel widths.
† Pope, Setco, and Whitnon.
• Setco

 

ROTATION:

RH: Right-hand threads for CCW spindle rotation.
LH: Left-hand threads for CW spindle rotation.
CAUTION!
Always Wear Safety Goggles When Griding.

68

William Sopko & Sons Co., Inc. ● 26500 Lakeland Blvd. ● Cleveland, Ohio 44132-2692 ● Order Desk (216) 289-1400 ● Fax (216) 289-1888